DRIVE PLUG AN SS - prosystemitalia.com

Download PDF

Application

Hammerset Anchor for multiple attachment in cracked and single attachment in non-cracked concrete.

Suitable for fixing pipelines, channels, etc. meeting the respective approval requirements. To be used in structural parts under dry indoor conditions, as well as outdoor constructions (including industrial ambiance and coastal areas) or damp locations provided no special aggressive conditions are given.

- No special drill is required

- Setting Tool for Drive Plug is to be used as setting tool

for distance-controlled forced expansion

- Suitable for put-before assembly

Installation

As setting tool the respective expansion cone for drive plus is to be used.

The "intelligent" expansion cone facilitates the assembly with drill hole tolerances in the bore hole diameters or with different concrete.

Due to the controlled expansion the needed edge and centre distances are considerably reduced.

Technical Data

General installation data:

Anchor size	M8x30	M8x40	M10	M12
Perm. load for single anchor C20/25-C50/60 [kN]	1.7	2.0	2.0	2.4
Perm. bending moment (A4-70) M_perm [Nm]	11.9	11.9	23.8	42.1
Characteristical centre distance s_cr [mm]	180	210	170	200
Characteristical edge distance c_cr [mm]	90	105	85	100
Loads under fire exposure
Perm. load R30 perm. F [kN]	0.9	0.9	1.5	1.5
Perm. load R60 perm. F [kN]	0.9	0.9	1.5	1.5
Perm. load R90 perm. F [kN]	0.9	0.9	1.5	1.5
Perm. load R120 perm. F [kN]	0.4	0.4	1.0	1.2

Anchor size	M8x30	M8x40	M10	M12	M16
Nominal dia. of drill d₀ = [mm]	10	10	12	15	20
Depth of drill hole h₀ = [mm]	30	40	40	50	65
Tightening torque when anchoring T_inst = [Nm]	8	8	15	35	60
Pass-through hole in component to be joined d_f ≤ [mm]	9	9	12	14	18
Thread length L_th [mm]	13	20	15	18	23
Minimum screw-in depth L_sdmin [mm]	9	9	11	13	18
Minimum thickness of component h_min [mm]	100	100	130	140	160
Min. centre distance s_min [mm]	60	80	100	120	150
Min. edge distance c_min [mm]	95	95	135	165	200

Anchor size	M8x30	M8x40	M10	M12	M16
Perm. tensile load C20/25 [kN]	3.3	3.6	6.1	8.5	12.6
Lateral tension perm. V ≥ C20/25 [kN]	4.6	4.6	6	11.9	19.2
Bending moments perm. M [Nm]	11.9	11.9	23.8	42.1	106.7

Material: Stainless steel A4 (316).

Type	Drill hole ø x depth [mm]	Thread ø x length [mm]
M8 x 30	10 x 30	M8 x 13
M8 x 40	10 x 40	M8 x 20
M10 x 40	12 x 40	M10 x 15
M12 x 50	15 x 50	M12 x 18
M16 x 65	20 x 65	M16 x 23

Approvals

For the multiple fixation of non-structural systems Approval ETA-10/0258 (M8-M12), for anchorage in non-cracked concrete Approval ETA-10/0257 (M8-M16), Fire Protection Certification, VdS-conform, FM-Approval ≥ M10.