![BOLT ANCHOR AN BZ PLUS](https://www.prosystemitalia.com/c/337-category_default/bolt-anchor-an-bz-plus.jpg)
BOLT ANCHOR AN BZ PLUS
Application
Universal use for anchorage of heavy loads even in areas with cracked concrete.Suitable for anchoring pipes, chennels, brackets and support plates in closed environments to the exclusion of damp environments.
- No special drill required.
- Simple and quick mounting.
- Drive-in hammer zone for preventing any thread damage
Scope of delivery
Supplied with washer and hexagon nut.
Installation
1. Drill bore hole according to the minimum bore hole depth
perpendicularly to the surface.
2. Remove dirt from hole.
3. Drive the anchor into concrete up to its embedment mark.
4. After tightening the anchor with a torque wrench Tinst (see torque indicated in the following tab),
it may immediately be submitted to loading.
Note the instructions in the mounting manual!
Technical Data
Standard anchoring depth:
Type | M8 | M10 | M12 | M16 |
---|---|---|---|---|
Perm. load 1) tension C20/25 2) [kN] | 2.4 | 4.3 | 7.6 | 11.9 |
C25/30 2) [kN] | 2.6 | 4.7 | 8.3 | 13.1 |
C30/37 2) [kN] | 2.9 | 5.2 | 9.3 | 14.5 |
C40/50 2) [kN] | 3.4 | 6.0 | 10.8 | 16.8 |
C50/60 2) [kN] | 3.7 | 6.6 | 11.8 | 18.5 |
Perm. load 1) oblique ≥ C20/25 2) [kN] | 8.6 (5.0)3) |
12.6 (6.5)3) |
17.1 (8.5)3) |
26.9 (23.6)3) |
Perm. bending moment 1) [Nm] | 13.1 | 26.9 (25.7)3) |
46.9 (44.6)3) |
119.4 (99.,9)3) |
Min. thickness of component hmin ≥ [mm] | 100 | 120 | 140 | 170 |
( 3 hef ) Charact. centre distance scr [mm] | 138 | 180 | 210 | 255 |
( 1.5 hef ) Charact. edge distance ccr [mm] | 69 | 90 | 105 | 127.5 |
Min. centre distance s at/edge distance c ≥ [mm] | 40/70 | 45/70 | 60/100 | 60/100 |
Min. edge distance c at/centre distance s ≥ [mm] | 40/80 | 45/90 | 60/140 | 60/180 |
Effective anchoring depth hef [mm] | 46 (35)3) |
60 (42)3) |
70 (50)3) |
85 (64)3) |
Nominal diameter of drill d0 [mm] | 8 | 10 | 12 | 16 |
Depth of bore hole h1 ≥ [mm] | 60 (55)3) |
75 (65)3) |
90 (75)3) |
110 (95)3) |
Anchoring torque Tinst [Nm] | 20 (15)3) |
25 (30)3) |
45 (50)4) |
90 (100)3) |
Perm. load 4) for fire exposure | ||||
Perm. load R30 perm. F [kN] | 1.3 | 2.2 | 3.2 | 6.0 |
Perm. load R60 perm. F [kN] | 1.1 | 1.8 | 2.8 | 5.2 |
Perm. load R90 perm. F [kN] | 0.8 | 1.4 | 2.4 | 4.4 |
Perm. load R120 perm. F [kN] | 0.7 | 1.2 | 2.2 | 4.0 |
1) Loads for single anchors without influence of edge distances
2) Cracked concrete (option 1)
3) Edge/Centre distances in case of fire - respective approval is to be respected
Reduced anchoring depth:
Anchor size | M8 | M10 | M12 | M16 |
---|---|---|---|---|
Perm. load 1) tension C20/25 2) [kN] | 2.4 | 3.6 | 6.1 | 9.0 |
C25/30 2) [kN] | 2.6 | 3.9 | 6.6 | 9.8 |
C30/37 2) [kN] | 2.9 | 4.3 | 7.4 | 10.9 |
C40/50 2) [kN] | 3.4 | 5.1 | 8.6 | 12.7 |
C50/60 2) [kN] | 3.7 | 5.5 | 9.4 | 13.9 |
Perm. load 1) oblique ≥ C20/25 2) [kN] | 7.0 | 10.4 | 14.5 | 21.6 |
Perm. bending moment 1) [Nm] | 13.1 | 26.9 | 46.9 | 123.4 |
Min. thickness of component hmin ≥ [mm] | 80 | 80 | 100 | 140 |
(3 hef ) Charact. centre distance scr [mm] | 105 | 120 | 150 | 195 |
(1,5 hef ) Charact. edge distance ccr [mm] | 52.5 | 60 | 75 | 97.5 |
Effective anchoring depth hef [mm] | 35 | 40 | 50 | 65 |
Nominal diameter of drill d0 [mm] | 8 | 10 | 12 | 16 |
Depth of bore hole h1 ≥ [mm] | 49 | 55 | 70 | 90 |
Anchoring torque Tinst [Nm] | 20 | 25 | 45 | 90 |
1) Loads for single anchors without influence of edge distances
2) Cracked concrete (option 1)
Type | Thread connection |
Standard anchoring depth tfix |
Reduced anchoring depth tfix |
Total length [mm] |
---|---|---|---|---|
8/10/21/75 | M8 | 10 | 21 | 75 |
8/30/41/95 | M8 | 30 | 41 | 95 |
10/10/30/90 | M10 | 10 | 30 | 90 |
10/20/40/100 | M10 | 20 | 40 | 100 |
10/30/50/110 | M10 | 30 | 50 | 110 |
10/50/70/130 | M10 | 50 | 70 | 130 |
12/15/35/110 | M12 | 15 | 35 | 110 |
12/30/50/125 | M12 | 30 | 50 | 125 |
12/50/70/145 | M12 | 50 | 70 | 145 |
16/25/45/145 | M16 | 25 | 45 | 145 |
16/50/70/170 | M16 | 50 | 70 | 170 |
Approvals
Approval ETA-10/0259
FM-approval for M10, M12, M16
VdS-conform for all sizes
Shock approval of the Federal Office for Civil Defence, Bern (Switzerland)
![BOLT ANCHOR AN BZ PLUS](/pim.prosystemitalia.com/storage/private/files/Image_set_categorie_b2b/9f9ca2b767a1afb31e1a65b47d367efaa6f8bf07.png)
![BOLT ANCHOR AN BZ PLUS](/pim.prosystemitalia.com/storage/private/files/Image_set_categorie_b2b/1a1ac8ba8340bd01afd2910db150390b56f57dc4.png)
![BOLT ANCHOR AN BZ PLUS](/pim.prosystemitalia.com/storage/private/files/Image_set_categorie_b2b/db012f06267908ec64406ce463a304ae2647d793.png)
Code | Name | Weight | Number of pieces | ||
---|---|---|---|---|---|
114135 | M 8/10/21/ 75 mm * | 0.03 | 100 | Information request | |
114136 | M 8/30/41/ 95 mm * | 0.04 | 100 | Information request | |
114140 | M10/10/30/ 90 mm | 0.06 | 50 | Information request | |
114142 | M10/30/50/110 mm | 0.07 | 50 | Information request | |
114143 | M10/50/70/130 mm | 0.08 | 50 | Information request | |
114147 | M12/15/35/110 mm | 0.10 | 25 | Information request | |
114144 | M10/50/70/130 mm | 0.09 | 50 | Information request | |
114148 | M12/30/50/125 mm | 0.11 | 25 | Information request | |
114149 | M12/50/70/145 mm | 0.13 | 25 | Information request | |
114155 | M16/25/45/145 mm | 0.23 | 20 | Information request | |
114156 | M16/50/70/170 mm | 0.26 | 20 | Information request |