RESIN ANCHOR ROD VMZ-A
Application
Anchor Rod for push-through and put-before mounting (for anchoring heavy loads).
Suitable for attaching pipelines, channels, brackets, etc. in closed rooms - except for damp locations.
(Stainless steel version available on request).
- No special drill required
- Heavy loads
- Small edge and centre distance
Scope of delivery
Pre-assembled with washer and hexagon nut.
Installation
1. Drill hole according to min. setting depth vertically to the surface.
2. Careful cleaning of drill hole with Steel brush and Blow-Out Pump.
3. Screw Mixing Nozzle onto the cartridge; foreshots to be removed and fill 2/3 of drill hole with resin starting from botton of the hole.
4. Drive the anchor manually into plastered borehole up to its embedment mark.
5. When reaching the embedment mark, plaster must be apparent.
6. Respect hardening time, when tighten the anchor with instructed torque.
Detailed assembly instruction is attached to the product.
Technical data
| Type | M12 | M16 |
| Perm. load 1) tension C20/25 2) [kN] | 12.3 | 24.0 |
| Perm. load 1) tension C25/30 2) [kN] | 13.5 | 26.4 |
| C30/37 2) [kN] | 15.0 | 29.2 |
| C40/50 2) [kN] | 17.3 | 33.8 |
| C50/60 2) [kN] | 19.0 | 37.1 |
| Perm. load 1) oblique V C20/25 2) [kN] | 19.4 | 36.0 |
| ≥ C30/37 2) [kN] | 19.4 | 36.0 |
| Perm. bending moments M [Nm] | 60 | 152 |
| Min. thickness of component hmin ≥ [mm] | 110 | 170 |
| Charact. centre distance Scr,N [mm] | 240 | 375 |
| Charact. edge distance Ccr,N [mm] | 120 | 187,5 |
| Min. centre distance s at/edge distance c ≥ [mm] | 55/80 | 70/90 |
| Min. egde distance c at/centre distance s ≥ [mm] | 55/80 | 70/110 |
| Effective anchoring depth hef [mm] | 80 | 125 |
| Nominal diameter of drill do [mm] | 14 | 18 |
| Depth of bore hole h0 [mm] | 85 | 133 |
| Anchoring torque Tinst [Nm] | 40 | 60 |
| Loads under fire exposure | ||
| Perm. load R 30 perm. F [kN] | 5,8 | 7,67 |
| Perm. load R 60 perm. F [kN] | 3,8 | 5,81 |
| Perm. load R 90 perm. F [kN] | 1,81 | 4,01 |
| Perm. load R 120 perm. F [kN] | 0,81 | 3,11 |
1) Loads for single anchors without influence of edge and centre distances, if constant temperature of 50°C and und currently 80°C is not exceeded.
2) Cracking concrete 50°C/80°C
The safety factor according to ETAG is included.
For the dimensioning, respect the data of the approval notification.
Material:
Steel, galvanised
Approvals / Compliance
Sikla Approval ETA 10/0260
| Type | Thread connection | tfix = Max. usable length [mm] | Total length [mm] |
| VMZ-A M12-25/125 | M12 | 25 | 125 |
| VMZ-A M16-30/180 | M16 | 30 | 180 |
| Code | Name | Weight | Number of pieces | ||
|---|---|---|---|---|---|
| 190739 | M12-25/125 | 0.06 | 10 | Information request | |
| 190775 | 0.13 | 10 | Information request | ||
| 190793 | 0.28 | 10 | Information request |